- Standard ground shipping within the contiguous 48 states. Alaska & Hawaii shipping costs extra.
- Total order must be over $99 after all discounts.
- For more information, please see Shipping Included.
Lelit PLA2206 Dark Walnut Flow Control Kit
$249.99
- Must be logged into your online account when purchasing to accrue EspressoPoints.
- For more information, please visit EspressoPoints.
- Parts are non-returnable and non-refundable unless damaged in transit.
- Parts do not include any over the phone technical support or instructions other than what is provided on the website.
- Parts do not come with any warranty.
- For more information, please see Terms & Conditions.
This product is already in your quote request list.
SKU: PLA2206
Categories: Lelit Espresso Machines & Related Parts, Espresso Parts, Lelit Espresso Machine and Espresso Grinder Parts
Lelit PLA2206 Dark Walnut Flow Control Kit
This flow control kit (PLA2206) is for the Lelit Mara X espresso machine models.
Please note that Lelit confirms this item fits the Lelit Mara. However, they can not confirm it fits E61 groupheads found on other machines. Lelit has confirmed that other machines can have a slightly different E61 grouphead. This item is considered a part, and not an accessory.
It is confirmed this paddle kit will not work on Vibiemme E61 groupheads due to the different structure of the top of their E61.
Please note the following to avoid damage to your grouphead:
From the top of your grouphead, the gicleur can be removed usually with an 8mm socket and socket wrench. Upon installation, needle nose pliers can be used to start the installation of the new gicleur. Otherwise, place a little white masking tape on the inside of the 8mm socket to hold the gicleur in place.
WARNING!!!! Upon installation, only hand tighten the gicleur. If you use a socket wrench, there is a 99% likelihood that the gicleur will break inside the grouphead and can be difficult to remove.
If you have success or not on your E61, please write your review to make other customers aware. In your review please note your machine manufacturer and model.
PDCFK01WLW0ZXX1
| Brand | Lelit |
|---|
Leave your review
Rating
Publish review
Submit Questions for FAQ
Please review the FAX to confirm the question or topic was not previously covered.
Any followup questions for FAQ should be requested as a separate FAQ submission.
-
This flow control kit fits the Rocket Cincuantotto but doesn’t work properly. The paddle doesn’t allow the flow device to turn enough, so when it’s fully open, the flow rate is constricted. It needs to turn more in order to open up the pin more. A work around is to calibrate the flow rate on the open setting to 250g/25sec and when it’s “closed”, the flow rate is minimal. Another work around would be to change the wood paddle for another fitting, but that’s a hassle. I advise to not buy this kit. Unfortunately I did, and 1st Line doesn’t allow returns. They took a while to respond to my first question, and didn’t respond with a definitive answer. I was also impatient and a bit stubborn. I wanted this wood paddle. I’m wondering if their own “Lelit” kit, which is different than this one, would work.
-
Q This flow control kit fits the Rocket Cincuantotto but doesn’t work properly. The paddle doesn’t ...... Read more answer nowAsked on February 15, 2024 4:10 pmA
The two Lelit kits are the same. This kit was finally made by Lelit after a few years of us requesting it from Lelit. The more expensive one was a bundling we put together on our web site by ordering all the separate components from Lelit - since we had to buy each piece separately,we paid more and of course, it cost us more. The pieces are the same between the two.
Correct, we could not respond with a definitive answer. The question is always simple, but the answer takes research time - in this case, we would have to take the Rocket machine out of the box, install the kit, warm up the machine, fully test it, and then go backwards to remove the kit from the machine. This involves a technician. Our technicians are busy repairing machines as well as handling many other inquiries prior to yours - some of them requiring skilled technicians. We wish there was some patience.
We are sorry this did not work 100% for you. Hopefully, one of the workarounds suffice. We would agree with you to not buy this kit for Rocket espresso machines.
Will this fit a Rocket Cincuantotto? I imagine you know, but it has an e61 group head.
-
Q Will this fit a Rocket Cincuantotto? I imagine you know, but it has an e61 group head. answer nowAsked on February 8, 2024 8:33 pmA Every E61 grouphead by different manufacturer can have slight differences. Sorry, to answer this question is not an easy answer. If it was, we would have published it. This is why we make a statement that flow control kits may not fit groupheads by a different manufacturer.
