*SOLD* SIDEWALK SALE – Quamar Q50E Electronic Stepped Doserless Espresso Coffee Grinder OPEN BOX (E013)

Quamar Q50E Electronic Stepped Doserless Espresso Coffee Grinder

Coming soon…

Grinding adjustment

• Stepped: Adjustment dial is located underneath the hopper. The entire dial has a numbering system so you can remember your current grind setting easier. Turn clockwise for a coarser grind and counterclockwise for a finer grind.
• Setting lock: A setting lock button keeps your current setting. This helps prevent users from accidentally altering it and spending time to find your correct setting again.

Grinding burrs

• Flat burrs: Large size at 54 mm. The larger the size, the more of a grinding surface, resulting in faster production.
• High rpm: Faster spinning rate at 1400 rpm. The higher the speed, the faster the production, which can increase efficiency and reduce wait times.
• Easy access: Remove the bean hopper. Turn the grinding adjust to the coarser direction until the top assembly comes off. This will give you access to the burrs and the grinding chamber. The burrs themselves are held in with Allen key screws.

Electronic controls

• Multiple dosing options: There are 3 dosing options. Single dose, double dose, and manual dose.
• Time based grinding: You can adjust the the time for each automatic dose up to 640 seconds max. Adjustments change by 0.05 second increments.
  Power save mode – You can set the LCD display to dim after a certain time (from 1 minute to 999 minutes).
• Burr replacement: You can set an alert for when your grinding burrs will need to be replaced (up to 200,000 doses or can turn off at 0 setting). Recommended setting is at 50,000.
• BAR message: Customize your LCD display with a short message (ex. the current blend of beans in the hopper).
• Brightness option: The brightness of the LCD display can be adjusted up or down to your comfort level.
• Dosing count: This helps keep track of usage. Displays the total count (from 1st use), partial count (from last reset), and missing count (amount remaining until burr replacement alert).
• Language option: A total of 8 languages available: Italian, English, German, French, Dutch, Spanish, Portuguese, Polish.
• Password protection: You can enable a password so other users cannot change your settings.

Bean hopper

• Low profile: The total height of the grinder without the hopper is a little under 12″. The bean hopper adds another 4.5″ bringing the total height to approximately 16.5″. The total capacity is approximately 1/2 pound of whole coffee beans, about a quarter of the size of a standard kilo bag.
• Set screw: Secures the hopper to the grinder. This serves as a reminder for users from quickly removing an already filled bean hopper.
• Fingerguard: Prevents users from “accidentally” putting their fingers in the grinding burrs.
• Stopper: A door near the bottom of the hopper can be pushed in to close the opening. This allows you to remove the hopper with beans inside so you can easily change the beans. There will be some beans already in the burrs which will have to grind out first before removing the hopper.

Accessories included

• Tamper: A cheap plastic tamper. You can use as a backup just in case you lose your current one.
• Instruction manual: Written in 6 languages: Italian, Spanish, Polish, English, French, German. Instructions also work for the M80, Q13, & T48 models.

Espresso Coffee Grinder Warnings:

• Roast Profiles: Espresso grinders sold by 1st-line Equipment, unless specifically indicated on the grinder page, are manufactured for coffee beans that have Italian or espresso roast profiles. Lighter roasted coffee beans may clog the grinder or not grind fine enough. Darker roasted coffee beans, such as French roasted or oily coffee beans, may clog the grinding chamber and/or the grinder chute where the ground coffee exits.
• Changing grind settings: It is very important to only change grind settings when the unit is powered on and the burrs are in motion. If you do not do this, the burrs will ‘gunk’ up and render the grinder to only produce very coarse grinds or no grinds at all. To remedy this, you will have to open up the grinder to get access to the grinding burrs. This issue will be considered operator error for lack of following directions, and not be classified as a defective grinder.
• Electrical cord: For most grinders, the cord is placed between the packaging (foam or cardboard) and the underside body of the grinder. During shipping, it is normal for a bend or insignificant blemish/slice to damage the cord.
• Finding coffee grinds in a new grinder: Most manufacturers test their grinders with coffee beans before they leave their facility. Unfortunately, they are not always able to get every trace of coffee out of the grinders after testing. As a result, you may find coffee beans or grinds inside your grinder, or there may be grinds in the packaging.
• Static issues: There are static issues with all grinders, even the highest-quality models. We firmly believe that the static comes from the coffee beans. If you are having static problems with your coffee grinder, try using a different blend of beans.
• Electrical: To avoid electrical damage (which is not considered a manufacturer's defect), please acquire and install a single-outlet surge suppressor rated at 1080 joules or higher. A surge without protection can damage a grinder at the power switch, the capacitor, the motor, or the wiring.
• Burr cleaning: For routine maintenance of the grinding burrs, we recommend using grinder cleaning agents. We do not recommend any removal of the burrs or the burr carrier for cleaning (unless necessary) as re-assembly can cause damage. If the grinder chamber is dis-assembled, the warranty is voided for any damages that result. It is important to always remove all coffee grinds from the threads of the burr carrier and the grinding chamber.
• Replacing burrs: NEVER use a flat head screwdriver and hammer to wedge UNDER the burrs for removal. This could badly damage your grinder.