Lelit Victoria PL91T PID Single Boiler Espresso Machine

Yes, the switch needs to be replaced. We strongly suggest geting a surge suppressor as we describe.

Hi,

We only service & carry parts for 110V home machines.

Yes, remove water softener from reservoir, fill with white vinegar and run through the steam/hot water wand. It may or may not correct any damage from over-tightening.

This either comes from water corrosion build up in the valve or overtightening it. 

Remove the water softener from the reservoir. Please run a descaler, such as 16 ounces of white vinegar, through the wand and let sit for 8 or more hours, then rinse a half tank through the wand and then test. If it fails, please contact us if you purchased the machine from us, or the reseller if you purchased elsewhere.

Hi,

Sorry, we currently do not sell puck screens so we cannot confirm how tight 58.5mm will be.

Hi,

Please see SKU XMC020-LELIT.

Just a spout or the entire portafilter? If just a spout, wide or narrower style?

It may be condensation from warming up. We see this behavior this time of year. Upon further use, please listen for a hiss. If there is a hiss, please power off the machine and contact us.

Last we checked, the machine shows the temperature as it is climbing.

Sorry, at this time, we do not have any recommendations knowing a good fit.

Hi,

We spoke with Lelit and confirmed this was an error on our website. We have updated the description. We apologize for the confusion.

We are very sorry as Lelit does not offer this o-ring separately. We usually just put a little plumber's tape on the threads.

Yes, there is a little scratching on the tank when pulling in and out. Yes, you can shave the metal tabs if you like.

Lelit, as well as other manufacturers, will not cover the OPV if modified. Lelit uses a sealant to hold the OPV in place. If the screw is modified, there is a chance it will strip the screw.

Please review the diagrams for parts. Sorry, we try to not point to parts because they can change in the future.

We are very sorry that we do not carry this item at this time.

Please allow to get back to brew temp first. Otherwise, the heating element on the machine can be damaged on the next start up.

1) I have read that the machine reminds you to run the steam wand after steaming by turning on the pump. What does this mean exactly? After I press the steam button after steaming, so the machine returns to espresso mode, I have to open the steam valve as well and let it run?

---Yes.

If so, how long do I have to let it run for before closing the steam valve?

---Until the pump stops.

2)I'm curious if you recommend keeping it on in between use?

---Best to power off so there are less life cycles used on the heating element as well as reducing the possibility of damage from electrical surges

If I use it at 9am, and then again at 2pm, should I turn it off and on again in the afternoon?

---Strongly recommended.

Or leave it on the entire time? What is the eco mode exactly and can I tell when it is triggered, or does it happen automatically after 30 min of no use?

---It reduces power consumption. Please refer to the owners manual as some mush older versions did not have this.

Please look in the specifications tab of this machine.

Sorry, the current version does not. There has been no recent information from Lelit about placing their new pump on the Victoria.

The power switch, steam wand grip protector, and displays are in black. The symbols, portafilter and steam knob are in brown. The other portafilters, except Marzocco and 1st-line 7.5mm lips, should work.

In our opinion, you probably do not need a dual boiler.

As for the water, descaling eventually eats away at the internal components. We prefer prevention with the use of a water softener, which we asked Lelit to include with the machines. Dual boilers have more stringent requirements for water usage because of the auto refill circuitry. The Victoria has a wider range in water usage.

Hmmm. You may want to check with your dealer.  After the steam is turned off, the pump will auto activate to run water through the boiler, basically reminding you to open the steam valve.  This will refill the boiler and bring the temperature down.

Backflushing and water softening recharging are the key. Clean the reservoir every 2 weeks with dishwash soap and rinse. No dishwasher.

First thing on GFIC, please read.

Second, always refer to the parts diagrams and search for parts on our web site for availability and pricing.

The 30 minute stand by mode saves energy as well as help preventing the boiler's heating element from burning out.

Hi,

Here is a link to the Lelit Victoria parts diagram.

Here is a link to the grouphead gasket.

Please always refer to the parts diagrams on our web site. We are out of stock at the moment, but they should be in stock in early January.

The Casa V is by ECM and is a more simple machine controlled by thermostats for coffee and steam mode.

The Lelit Victoria has a LCC which manages the temperature through a PID sensor for coffee and steam modes. It also has a brew pressure gauge to help you if you need to make the grind finer or coarser. Lastly, ont he Victoria, as soon as steam mode is turned off, the pump automatically kicks in to refill the boiler so it does not get burned out from lack of water - the user needs to remember to open the steam valve. On other machines, the user has to manually turn on the coffee or hot water switch and open the steam valve to refill the internal boiler. If forgotten, the heating element can damage as no single boiler machines refill the boiler from the reservoir automatically after steaming.

Sorry, we checked on the Bianca reservoir, and it does not fit.

As for extra baskets, we do have them on our web site.  Most 58mm baskets do fit the Victoria portafilter.

Lelit just provided the following documentation.

Sorry, we do not answer with promotional deals as they change over time. Some manufacturers do ask that certain products be removed from promotional offers.

As for technical support, we can assist those customers under warranty via phone, email, and in some cases with video (where we made videos). For out of warranty machines, support is handled via our Q&A tab on the product page. In either case, where a customer is not mechanically inclined, the machine can be shipped to us in NJ for repair. If out of warranty, customers can go to any third party repair center and then just order the parts from us.

Sorry, the 2016 model is no longer available.

In July 2020, we started shipping the 2020 version.

We are hoping by the end of July. Sorry, COVID-19 impacted production schedules at many European suppliers.

1. Coffee taste can be different, better or worse is an opinion.
2. Changing temprature for steam depends upon how small or large the vessel is for the milk.
3. Bets to shut off the machine if not being used within 30 minutes.

Sorry, we do not have any Victorias in stock to double check.

The reading on the brew pressure gauge is related to the puck in the filter basket. Please read our article about this.

Others might work, but we are unable to guarantee it.

Our advice always given, never use the 1 cup basket. It is difficult to achieve good results. If you are achieving 9 bars, then the machine is working properly. The strength of the espresso is then the characteristic of the espresso beans.

On point 1, 15 minutes is a long time. It should be up to 5 minutes.  After steaming milk, you do need to open the steam wand and shut off the steam button. Then allow the temperature to come back down by allowing the machine to cycle cold water through the boiler. If you do not do this, then it can take 15 minutes for the temperature to drop from steaming mode to coffee mode.

On point 2, this is correct.

Hi,

We currently have stock of the 2016 version. Once we clear out and bring in the new version, we will update the description (and price) with the changes.

Hi,

For backflushing, we recommend the Ascaso Detergent.  Here is a link to the instructions.

The coffee and hot water temperature are on the same setting.

To change the temperature of the hot water (and grouphead). Press the "-" button to get into the menu. The first option is the hot water/grouphead temperature. Press "+" to get into this setting. You should see the temperature blinking. Then use the "-" or "+" to change the temperature. After a few seconds, your setting will save. Please note when navigating through the screen, you must press the buttons within a second or two. Otherwise, it will revert to the previous screen.

Lock to be tight and no leaks. Eventually, it will move over. Try without coffee, and this is where you should end. If you don't with coffee, then you have too much coffee in the basket.

The filters function in the same way. We hope your dogs are ok.

Please note that we do bench test every Victoria espresso machine with water only prior to shipping.

Please make sure the magnetic float tube is on the left hand side of the reservoir when inserting it into the machine. In addition, with the water reservoir empty, flip it upside down to make sure it moves within the tube. Lastly, make sure the reservoir engages the switch on the front panel inside the reservoir section.

The OPV is way down below in the back in front of the reservoir. The machine will need to be disassembled.  However, the grind fineness and amount of coffee in the basket are the parameters that create the resistance for the pump to push the water through. Hence, the flow control or brew pressure is managed with these parameters.

The tamper needs to fit the 58mm baskets on the Victoria. Any quality 58mm tamper will work great! As for the levelers, Lelit makes the best one!

Sometimes, the water from testing dries in the gauge capillary tube. Running 2 cups white vinegar through the grouphead (no filter attached in tank) and let sit for 20 minutes. Repeat with another 2 cups and and 20 minutes, Then rinse water reservoir and fill half way with water and through grouphead and steam wand (half and half). This should clear the capillary tube.

Pump pressure.

The steaming mode typically will switch to coffee made once the steaming button is depressed off after an amount of time has passed (Lelit does not say how long, but we believe about 2 minutes). So far, no one has complained about this steaming function.

Once the steam function is depressed off, the pump is turned on and this is the audible alert. This function saves the machine from the lack of the proper water level inside the boiler (not the reservoir).

These are ALL guidelines. At the end of the day, try and use whatever works and tastes best in your cup.

Please read our knowledge base to learn more on making espresso.

This is most likely the OPV relieving over pressure tot he drip tray.

The screw can be removed for deeper cleaning of the grouphead screen and parts. When tightening, hand tighten and then 1/8th turn tight with the Allen key.

Yes, this is a built-in safety feature to prevent damage to the machine.

The Victoria with a PID will allow you to reduce the temperature through the PID display so you have a lower boiling point. Unfortunately, there is not much that can be done on the PL041QE as it has thermostats.

Yes, there is an adjustable OPV valve, but it is not easy to get to.

The top panel (2 screws), back panel (5 screws), and internal tank panel (6 screws) need to be removed to access.

One may ask why? The reason is that vibration pumps pump enough pressure to pump the water to pass through the resistance created in the espresso puck - the grind fineness, the amount of coffee in the basket, and the tamping pressure all relate to the resistance. Hence, the pump pressure can be controlled through these 3 paramaters.

The OPV, a.k.a. overpressure valve, only manages the maximum pump pressure by opening the valve when the pump achieves the set point on the OPV. However, it does not control anything lower. Hence, if the grind fineness, amount fo ground coffee, or tamping pressure is off, the OPV does not always help.

The timing is different based on different ambient temperatures, different actual voltages in the outlet, and some other stuff. Typically, we see about 30-45 seconds for warm up to steam mode.

For cooling back down, this machine actually has a very nice feature to prevent damage to the heating element. When the steam button is depressed off, the pump engages to refill the boiler. When this happens, a empty cup needs to be placed under the steam tip and the steam valve knob needs to be turned to open the steam valve. Once the machine says OK or there is a steady stream of water without steam, then the machine's boiler is brought back near espresso mode temperature.

Choosing to brew or steam first becomes a personal preference as either process is ok.

The machine will state OK once the machine is at temp for espresso.