Bianca Flow Control Kit

Lelit Grouphead Flow Control Assembly with Paddle and Holding Screw

4.6 out of 5 based on 5 customer ratings
(5 customer reviews)

Bianca-fy your espresso! Learn more below! This kit is known to work on the Bianca, Mara line of espresso machines, and the Caffeum Perfectus Minima by ACS.

Note: All wood is natural and there will be variations in the color and finish.

WARNING! Please note that we are not responsible for any damage before, during, or after installation.  Damages can include, but not limited to

  1. over-tightening the gauge into the grouphead (causing the gauge thread to break and threading broken inside the grouphead),
  2. breaking of gaskets and o-rings,
  3. scratches on the mushroom,
  4. over-tightening of gicleur, and/or
  5. limescale build-up.

SKU: FlowPaddle Categories: , ,

Bianca Kit – Flow Control Assembly with Paddle and Holding Screw For Manual Brew Pressure Profiling

Please note that Lelit confirms this item fits the Lelit Mara. However, they can not confirm it fits E61 groupheads found on other machines. Lelit has confirmed that other machines can have a slightly different E61 grouphead. This item is considered a part, and not an accessory.

It is confirmed this paddle kit will not work on Vibiemme E61 groupheads due to the different structure of the top of their E61.

Please note the following to avoid damage to your grouphead:

From the top of your grouphead, the gicleur can be removed usually with an 8mm socket and socket wrench. Upon installation, needle nose pliers can be used to start the installation of the new gicleur. Otherwise, place a little white masking tape on the inside of the 8mm socket to hold the gicleur in place.

WARNING!!!! Upon installation, only hand tighten the gicleur. If you use a socket wrench, there is a 99% likelihood that the gicleur will break inside the grouphead and can be difficult to remove.

If you have success or not on your E61, please write your review to make other customers aware. In your review please note your machine manufacturer and model.

Brand

Lelit

Customer reviews

Rated 4.6 out of 5 stars
5 reviews
5 stars 4 80 %
4 stars 0 0 %
3 stars 1 20 %
2 stars 0 0 %
1 star 0 0 %

5 reviews for Lelit Grouphead Flow Control Assembly with Paddle and Holding Screw

Add a review

Use one of the allowed file type: jpg,png. The max size allowed is : 3 MB.

    This site uses Akismet to reduce spam. Learn how your comment data is processed.

    Ask a question

    Please ask follow up questions as a new question. Submitted questions will be first reviewed, answered, and lastly publicized.

      What is the difference between this flow control kit and the Lelit PLA2206 Dark Walnut Flow Control Kit? Why is this one so much more expensive? What about this other one you recommend for the Rocket machines? E61 Grouphead Flow Control Device I have a Rocket Cincuantotto and want a good flow control kit. I get the impression the Lelit one is better, but I might be mistaken. I do like the wood paddle in comparison to the little black knob on the E61 flow control kit.
    1. 0 votes
      Q What is the difference between this flow control kit and the Lelit PLA2206 Dark Walnut Flow Contr...... Read more answer now
      Asked by Robert Mangum on February 9, 2024 1:30 pm
      Answered by the admin This is a kit made by Lelit as before they decided not to make a kit but sell all the parts individually. Sorry, compatibility with Rocket Cinqcuantotto machines is not something we know off the top of our head. This is something that will take time as the machine has to be pulled down, a flow kit installed, and then tested. If it does not work, then we need to move on to the next flow control device. Unfortunately, we do not have technician standing around doing nothing as they take years to train and get caught up in repairs because there is a lack of technicians in our industry. Hence, we are very sorry that we will not have an answer in the near future.
      2. Is it possible to get a replacement screw? Lost the FS037 at some point for the paddle.
    2. 0 votes
      Q Is it possible to get a replacement screw? Lost the FS037 at some point for the paddle. answer now
      Asked by eszlsk on February 13, 2022 7:58 pm
      Answered by the admin

      We are sorry that we do not sell these crews separately. We believe they are a 2mm allen key screw.
      3. Is it possible for me to purchase the Lelit FC kit but with a black paddle instead?
    3. 0 votes
      Q Is it possible for me to purchase the Lelit FC kit but with a black paddle instead? answer now
      Asked by Long on January 31, 2022 3:51 pm
      Answered by the admin

      We are very sorry that it is not possible and there are no refunds nor returns on the order of this item.
      Answered by the admin

      Sorry, the black paddle is not available either.
      4. I have the flow control kit installed on my Mara X. Up until yesterday, all was well. Then I began to feel and see a fine stream of water spraying from the manometer connection. I have it tight but not so much that it is too tight. It's tight to where it has resistance and that's it. Why would this be happening?
    4. 1 vote
      Q I have the flow control kit installed on my Mara X. Up until yesterday, all was well. Then I bega...... Read more answer now
      Asked by Elaine Manfredi on December 18, 2021 9:13 pm
      Answered by the admin

      It may need a little plumbers tape or re-install.
      5. I have a Lelit Mara X and would like to keep the parts consistent. Is there anyway to buy this kit without the wooden handle but instead with the black handle provided with your alternative kit?
    5. 1 vote
      Q I have a Lelit Mara X and would like to keep the parts consistent. Is there anyway to buy this ki...... Read more answer now
      Asked by Chris on November 21, 2021 9:04 pm
      Answered by the admin

      Sorry, we are unable to break up kits into individual items.
      6. I'm interested to purchase a set of Flow control devices, and found out there are two similar versions available. I was just wondering what the difference between the two sets. $100 price difference is quite a lot.
    6. 0 votes
      Q I'm interested to purchase a set of Flow control devices, and found out there are two similar ver...... Read more answer now
      Asked by Sakol on June 24, 2021 2:30 pm
      Answered by the admin

      The different is in quality of the parts and the performance of the parts. Higher priced means better.
      7. has there been a successful install on a profitec pro 700?
    7. 0 votes
      Q has there been a successful install on a profitec pro 700? answer now
      Asked by Merritt H Howard II on May 3, 2021 9:54 pm
      Answered by the admin

      Sorry, we do not know, but the following flow control will work on Profitec and ECM.
      8. I have an ACS Minima and see that there are two other kits that 1st-Line provides (sku: E61GFR & CS0030). Which of the three performs the best on the Minima or is best suited to the machine? Also, can the Lelit kit be purchased without the paddle?
    8. 0 votes
      Q I have an ACS Minima and see that there are two other kits that 1st-Line provides (sku: E61GFR &a...... Read more answer now
      Asked by Dan Petersen on May 3, 2021 12:22 pm
      Answered by the admin

      The Lelit flow control works best on the Minima.
      9. Hello, when do you think y'all will have this in stock again?
    9. 0 votes
      Q Hello, when do you think y'all will have this in stock again? answer now
      Asked by Mark on November 27, 2020 5:55 pm
      Answered by the admin

      Sorry, no ETA. It has been difficult to get parts from Italy.
      10. will you be getting an of these Lelit flow adjustment group head kit with walnut paddle in stock any time soon? Should this work with a Izzo Alex Duetto e61 machine?
    10. 0 votes
      Q will you be getting an of these Lelit flow adjustment group head kit with walnut paddle in stock ...... Read more answer now
      Asked by Nick on November 23, 2020 6:11 pm
      Answered by the admin

      Sorry, some parts are difficult to get from Italy. For the Izzo and ECM machines with black knobs and handles, we recommend our alternative.
      11. Will this work on the La Nuova Era Cuadra without getting the accessory ECM mushroom? I don't recall the mushroom style that is present on the Cuadra
    11. 0 votes
      Q Will this work on the La Nuova Era Cuadra without getting the accessory ECM mushroom? I don't rec...... Read more answer now
      Asked by Perry Nguyen on October 6, 2020 7:29 pm
      Answered by the admin

      It has for other Cuadra customers, but as stated, we can never guarantee it.
      12. There are three prices on this page, which is confusing to me. If I purchase a Lelit PL62 Mara, which product do I need for flow control? Also. someone asked whether the Lelit flow control kit would fit a Bezzera with an E61 group head, and the most recent answer was “yes.” Can you confirm that?
    12. 0 votes
      Q There are three prices on this page, which is confusing to me. If I purchase a Lelit PL62 Mara, w...... Read more answer now
      Asked by dentino on October 3, 2020 8:06 am
      Answered by the admin

      Sorry that you are having a difficult time understanding the build to order. It is set up so customers can decide what they need and do not need.

      The first price, which is crossed out, is the total if purchased separately. The second price on top is starting selling price WITHOUT any options selected. The 3rd or bottom price is the price with any options selected.

      Although we can confirm a fitment to Bezzera E61 groupheads, we can not guarantee it. Unfortunately, there could be variations on E61 groupheads from Bezzera that we may not be aware of, or their E61 design may change in the future (and we will never remember to come back here and update the info).
      13. I just installed most of this kit on my Rocket Giotto Evoluzione espresso machine. However, I did not install the spring and guide into the discharge of the E61 group. I have read that this is optional on some discussions. That said, nobody has explained why it's optional, as well as why I should consider installing it. Can you elaborate on why it is included in the kit, why I might want to install it (benefit), as well as any reason not to install it? Right now, the flow valve is working just fine without that replacement. Thank you, Craig
    13. 0 votes
      Q I just installed most of this kit on my Rocket Giotto Evoluzione espresso machine. However, I did...... Read more answer now
      Asked by Craig Larson on September 11, 2020 8:31 pm
      Answered by the admin

      Your current spring will probably break because of the extra stresses placed on that spring.
      14. I recently purchased this kit for my Mara. As of yet I have not been able to regulate pressure. When the paddle is fully open, to the right, I get 10 bar pressure. Just off of the seat with the paddle to the left. Maybe an 1/8 inch or 3/16 of an inch of rotation, it will increase more slowly but still goes to about 9 1/2 bar. I have taken it apart and put it back together a few times with no change in function. I have used every spring combination in the bottom section of the group head. I have also changed my grind setting considerably with no real change in function other than taking longer to pour a target weight. Also I have watched every video I can find about this topic.
    14. 0 votes
      Q I recently purchased this kit for my Mara. As of yet I have not been able to regulate pressure. W...... Read more answer now
      Asked by Sean on August 7, 2020 2:03 am
      Answered by the admin

      Please only have one Bianca-designated spring in the bottom portion of the grouphead. We assume you are looking at the grouphead pressure gauge and NOT the brew pressure gauge on the front panel. Lastly, you may need to coarsen your grind.
      15. I mounted the Lelit Grouphead Flow Control Assembly on my Rocket R60V. Installation was easy but I am unable to fully close the needle valve. I can lower the needle by turning the handle clockwise, thereby reducing the flow until the needle's surrounding shaft touches the gicleur. I know this because when I first lowered the needle that far, the shaft would loosen the gicleur when turning it anti clockwise. However, even if fully closed, there is still water passing through the grouphead. The alternate mushroom (ECM ECMGC229901133) looks the same as the one used in the R60V, so I dont't think that that is the way to go for me. Is there any way you cant think of that would allow me to lower the needle farer without it's surrounding shaft touching the gicleur? Any help would be greatly appreciated.
    15. 0 votes
      Q I mounted the Lelit Grouphead Flow Control Assembly on my Rocket R60V. Installation was easy but ...... Read more answer now
      Asked by Thorsten on August 4, 2020 8:19 am
      Answered by the admin

      The gicleur may not be tight enough. But, too tight, and it will split into two. The needle needs to make full contact to make full closure. In some cases, there the mushroom sits the gicleur a little deeper, then full closure is not possible and a new mushroom is needed. However, this latter part does not seem to be your case.
      A I already sticked the gicleur with Microtec’s TEC-100, but to no avail. Anyway, thanks for answering!
      16. Hi When is the Lelit 1000185 E61 Grouphead Internal Pressure Profile Kit back in stock?
    16. 0 votes
      Q Hi When is the Lelit 1000185 E61 Grouphead Internal Pressure Profile Kit back in stock? answer now
      Asked by Dean Li on July 15, 2020 10:32 pm
      Answered by the admin

      They have arrived back in stock.
      17. hello, for the Lelit 410003 E61 Grouphead Wood Paddle, do you have color choices for the paddle? If not, what color is available now? I feel like the picture of the listing does not do your product justice. Thanks,
    17. 0 votes
      Q hello, for the Lelit 410003 E61 Grouphead Wood Paddle, do you have color choices for the paddle? ...... Read more answer now
      Asked by Dean on June 28, 2020 6:58 am
      Answered by the admin

      Thanks. Pictures do not do it justice. Since it is real wood, there are slight differences in shade of color.
      18. Does this kit fit the Expobar Brewtus IV (Expobar Office Minore here in NZ)?
    18. 0 votes
      Q Does this kit fit the Expobar Brewtus IV (Expobar Office Minore here in NZ)? answer now
      Asked by Joseph Bell on June 11, 2020 3:42 am
      Answered by the admin Sorry, we never sold Expobar espresso machines and we are unsure of a good fitment or proper operation.
      19. Hello I'm looking to order this for the MaraX, in regards to option 4, I see there are two pressure gauge kits the lelit branded one, and the V111K branded kit. Other than the required gaskets, does the v111k Kit have everything required to fit the MaraX? Also would option 6-7 be required for the MaraX, or are those for the non Lelit machines?
    19. 0 votes
      Q Hello I'm looking to order this for the MaraX, in regards to option 4, I see there are two pressu...... Read more answer now
      Asked by Joey on June 9, 2020 6:09 pm
      Answered by the admin On Lelit machines, we strongly suggest the Lelit gauge. Option 6 and 7 are for other machines.
      20. Is there a way to buy the spine brass insert that is used in the Lelit Bianca paddle? If not is there a way to buy just the paddle? How much would it cost?
    20. 0 votes
      Q Is there a way to buy the spine brass insert that is used in the Lelit Bianca paddle? If not is t...... Read more answer now
      Asked by Maks Shklyar on May 29, 2020 12:39 am
      Answered by the admin

      Sorry, there is not.
      21. Hi, will this assembly (Lelit Grouphead Flow Control Assembly with Paddle and Holding Screw) fit a Vesuvius?
    21. 0 votes
      Q Hi, will this assembly (Lelit Grouphead Flow Control Assembly with Paddle and Holding Screw) fit ...... Read more answer now
      Asked by Dean on May 28, 2020 11:47 pm
      Answered by the admin

      Sorry, we are not 100% sure as we discontinued the Vesuvius as soon as the Lelit Bianca espresso machine arrived at 1st-line.
      22. Does this fit quickmill e61 (Lucca M58)? Do I need the optional mushroom or no? Thanks.
    22. 0 votes
      Q Does this fit quickmill e61 (Lucca M58)? Do I need the optional mushroom or no? Thanks. answer now
      Asked by Joey Cerone on May 26, 2020 11:34 pm
      Answered by the admin

      Sorry, we are unable to confirm as we do not sell the Lucca lines.
      23. With this kit installed in Mara, does this mean you would typically also adjust the OPV to allow higher pressure so you can get the benefit of more fine-grained pressure control with the paddle?
    23. 0 votes
      Q With this kit installed in Mara, does this mean you would typically also adjust the OPV to allow ...... Read more answer now
      Asked by Tom on May 23, 2020 3:41 pm
      Answered by the admin

      We suggest not changing the OPV at this time as the pump is newly designed, and we are unsure if increasing the OPV resistance will damage the pump.
      A Not need to adjust the OPV, I installed it on the Mara X and there’s enough pressure and water flow to do profiling and keep the brew head pressure under 10 bars, preferably 9 bars. If I open the valve completely I get 11 bars with a blank basket in the portafilter. I did installed the pre infusion spring that comes with the kit, and removed the drain valve spring and cam from the Mara X bottom section of the brew head, as the Bianca doesn’t have it, and recommended by 1st Line-Equipments.
      24. Do you sell the heavy duty spring from the kit separately? If so, how can I order one? Thanks
    24. 0 votes
      Q Do you sell the heavy duty spring from the kit separately? If so, how can I order one? Thanks answer now
      Asked by Geoffrey on May 15, 2020 5:31 pm
      Answered by the admin

      Sorry, the spring is not available by itself.
      25. I purchased this kit order # 65912 and would like to know the specs for the bushing used in the paddle. I'm having custom wood made for my espresso machine and having another paddle created. I just need to know the specs of the bushing /insert in the paddle or the shaft used in the needle valve. I don't want to sacrifice the actual paddle to get the insert. Thank you
    25. 0 votes
      Q I purchased this kit order # 65912 and would like to know the specs for the bushing used in the p...... Read more answer now
      Asked by Michael K McCann on May 8, 2020 5:47 pm
      Answered by the admin We are very sorry, but to our knowledge, Lelit has not revealed these secrets. They have good reason as they want to slow down the competitive information to fast following competitive copycat companies.
      26. Following up on a question from a fellow in 2019. Has any of the pre-orders from back then confirmed it works on Quick Mill Machines? I have a QM67 and im really interested in this kit!
    26. 0 votes
      Q Following up on a question from a fellow in 2019. Has any of the pre-orders from back then confir...... Read more answer now
      Asked by Rafael on May 7, 2020 10:33 pm
      A Yes. Work great on my quick mill Alexia Evo.
      A I bought this kit and applied it to my qm67. It works very well. I'm a little dissatisfied with the operating range of the lever, but it's been changed to allow a much more diverse extraction.
      27. Will it work with a VBM Junior HX?
    27. 0 votes
      Q Will it work with a VBM Junior HX? answer now
      Asked by Natan Bandler on May 1, 2020 6:27 pm
      Answered by the admin

      Sorry, the design of the grouphead will interfere with the bottom half of the paddle. Hence, we have not tried it.
      28. Follow up question on removing the drain spring as part of the flow control kit installation, you answer yes, and the cam gasket, which one is the cam gasket? Is there a drawing of the Mara X group head showing the cam gasket?
    28. 0 votes
      Q Follow up question on removing the drain spring as part of the flow control kit installation, you...... Read more answer now
      Asked by EFRAIN FLORES-COLON on April 27, 2020 6:50 pm
      Answered by the admin Sorry, we do not have the Mara X diagram yet. If there is a lower spring, then the cam shaft has a gasket, which should be removed.
      29. I’m going to install the Lelit Flow Control assembly in my Lelit Mara X, should I remove the drain valve spring, ( the one under the per infusion chamber) since the Lelit Bianca does not have it for it to work properly?
    29. 1 vote
      Q I’m going to install the Lelit Flow Control assembly in my Lelit Mara X, should I remove the drai...... Read more answer now
      Asked by EFRAIN FLORES-COLON on April 26, 2020 10:15 pm
      A Hello I have put this conversion on a Lucca M58 V 1.0 and I didn't need to remove any spring just added the valve and changed the glacier nozzle the bolt with a pinhole in it and it all worked as it should. Hope this helped.
      Answered by the admin

      It is a good idea to remove the bottom most spring and cam gasket.
      A Which one is the cam gasket? Do you have a drawing of the Mara X group head showing the location?
      Answered by the admin Sorry, diagrams have not been available yet.
      A I tried it both ways and the only way that it worked was leaving the original drain valve spring in. Do not exchange it. Hope that helped
      30. The options are little bit confusing. The $262.26 option, looks like it includes the flow control kit (sku 1000185) and the wood paddle with screw, then optional items listed 4-9 looks like is part Of the $333.12 cost. Does the $333.12 kit includes everything on the list from 1-9? If this is the case then I wouldn’t need the Lelit PLA582W wood kit, I’m I correct? I already pre order the Mara X and the PLA58W kit, I would cancel the later if not needed.
    30. 1 vote
      Q The options are little bit confusing. The $262.26 option, looks like it includes the flow control...... Read more answer now
      Asked by EFRAIN FLORES-COLON on April 6, 2020 1:48 pm
      Answered by the admin

      The Lelit PLA582W wood kit would give you the wooden valve knobs.
      31. I have installed the paddle kit including the new spring and gicluer. The drain valve does not work. Any suggestions?
    31. 0 votes
      Q I have installed the paddle kit including the new spring and gicluer. The drain valve does not wo...... Read more answer now
      Asked by Robin on March 28, 2020 12:27 pm
      Answered by the admin

      When this happens, the very most bottom spring and cam shaft need to be removed from the bottom spout.
      32. i'd really like to install this kit (https://www.1st-line.com/buy/lelit-grouphead-flow-control-assembly/#kit-of-internal-components-for-grouphead) on my rocket r58. do instructions come with it? is there any way you could give me an overview on how to install it?
    32. 0 votes
      Q i'd really like to install this kit (https://www.1st-line.com/buy/lelit-grouphead-flow-control-as...... Read more answer now
      Asked by Erik Mangali on March 23, 2020 5:07 pm
      Answered by the admin

      As previously states, we can not guarantee this will work on your machine as we do not sell Rocket. We have made a video on how to install.
      A I just installed it on my Rocket Giotto Evoluzione and it works great. While complete instructions do come with the kit of parts, I highly recommend you watch Dave Corbey's Youtube video titled "Lelit flow valve install - ACS Minima" before doing the installation. Very informative and helpful. He gives great tips and instructions on adjusting the closed position of the valve which is key to your success.
      33. is the faema mushroom available? you said it was not available in a previous answer but it's showing as being available on the website
    33. 0 votes
      Q is the faema mushroom available? you said it was not available in a previous answer but it's show...... Read more answer now
      Asked by Erick Mangali on March 23, 2020 12:47 am
      Answered by the admin

      All answers are based on the time of writing. Inventory counts do change as we all as specifics over time.
      34. thank you for answering the question about this fitting on my rocket r58. is there anything else i can do to help me guestimate if this would work on the rocket? i found a parts catalog that shows an exploded view of the r58 grouphead. would you mind taking a look (page 12)? (link removed as we do not allow links to other web sites)
    34. 0 votes
      Q thank you for answering the question about this fitting on my rocket r58. is there anything else ...... Read more answer now
      Asked by Erick Mangali on March 18, 2020 10:49 pm
      Answered by the admin

      It looks like it will work, but the mushroom may need to be changed. At this time, we are out of stock on extra mushrooms.
      A could you please add a link to the (out of stock) mushroom?
      Answered by the admin

      https://www.1st-line.com/buy/grimac-faema-grouphead-mushroom/
      Answered by the admin

      https://www.1st-line.com/buy/grimac-black-o-ring-for-faema-grouphead-mushroom/
      A both mushroom parts you posted show as "in stock." also, does the kit include instructions?
      Answered by the admin

      Please follow instructions on our web site. Every new question needs to be posted as a new question, not as an answer to an existing question.

      Instructions are included at the time of this writing.

       
      35. has this been confirmed to work on a rocket r58?
    35. 0 votes
      Q has this been confirmed to work on a rocket r58? answer now
      Asked by Erick Mangali on March 18, 2020 8:53 pm
      Answered by the admin

      Sorry, it has not been confirmed as we do not sell Rocket.
      36. someone above had already asked about installing this on a rocket r58. have you found out if it works?
    36. 0 votes
      Q someone above had already asked about installing this on a rocket r58. have you found out if it w...... Read more answer now
      Asked by Erick Mangali on March 18, 2020 7:08 pm
      Answered by the admin

      Sorry, we are unable to confirm.
      37. I have an Alex Duetto II and it has a two piece mushroom. Will the above kit work with my machine? I see a review from another customer who installed it on a alex Duetto IV which had a one piece mushroom and they needed to buy the additional mushroom.
    37. 0 votes
      Q I have an Alex Duetto II and it has a two piece mushroom. Will the above kit work with my machine...... Read more answer now
      Asked by Jose on March 11, 2020 4:39 pm
      Answered by the admin

      Sorry, we are unable confirm for all Izzo machines as they have changed the mushroom over the years.  If your machine has a stainless steel mushroom or one piece mushroom, then a new mushroom will most likely be needed.
      A I wanted to confirm that the upgrade does indeed work with the Alex Duetto II. The Faema E61 g Mushroom does not work with the Alex, as the internal diameter of the mushroom has a diameter that is smaller than the spring of the OEM mushroom. If you want to replace the stock mushroom, Chriscoffee does sell replacements. Otherwise I'm enjoying this upgrade on my Alex Duetto II!
      38. Will this work on VBM Super domobar ?
    38. 0 votes
      Q Will this work on VBM Super domobar ? answer now
      Asked by Mark Liao on December 31, 2019 7:40 pm
      Answered by the admin

      Only if the bottom portion of the wood handle is shaved off.
      39. With the complete Lelit flow control kit shown on your website, do you include a mushroom that fits the ECM Synchronika and if not, what is the additional cost, assuming you have this available?
    39. 0 votes
      Q With the complete Lelit flow control kit shown on your website, do you include a mushroom that fi...... Read more answer now
      Asked by smg on December 20, 2019 4:43 am
      Answered by the admin The mushroom is an option in the drop down. It is usually needed with an extra o-ring for the ECM Synchronika espresso machine.
      40. I have an original 1963 Faema e61. Will this work on my machine?
    40. 0 votes
      Q I have an original 1963 Faema e61. Will this work on my machine? answer now
      Asked by John Hanna-Barton on November 29, 2019 10:50 pm
      Answered by the admin Sorry, we are unable to confirm a fit. We will venture (guess) to say it will not in this case.
      41. Will it work on a Bezzera E61 group?
    41. 0 votes
      Q Will it work on a Bezzera E61 group? answer now
      Asked by Christopher Skorton on October 23, 2019 11:02 pm
      Answered by the admin

      Yes, this will work.
      42. Would you be able to tell me which compact heat exchange machines you carry are fully and easily compatible with the Lelit Pressure Profile kit you offer? I’m considering the Lelit Mara, VBM Domobar Junior, and ECM Mechanika Slim. I know the Bezzera BZ10 wouldn’t work since that’s not an E61 group head. Thanks!
    42. 0 votes
      Q Would you be able to tell me which compact heat exchange machines you carry are fully and easily ...... Read more answer now
      Asked by Christopher Skorton on October 23, 2019 3:15 pm
      Answered by the admin
      Proven to work on Mara. It does not fit the VBM. It will not work well on ECM machines as the mushroom needs to be changed.
      43. I want to ask if Lelit Grouphead Flow Control Assembly with Paddle and Holding Screw will fit my espresso machine (Profitec 700 pro) or not.
    43. 0 votes
      Q I want to ask if Lelit Grouphead Flow Control Assembly with Paddle and Holding Screw will fit my ...... Read more answer now
      Asked by Ahmed on September 9, 2019 3:28 pm
      Answered by the admin

      It has fit for other customers. However, we can never guarantee it.
      44. I ordered the flow control assembly. When installed, I didn't change out the restrictor(or gicleur). As a result, the needle on the regulator head was damaged(bent). Can I order just the regulator head, not the whole assembly? Thanks,
    44. 0 votes
      Q I ordered the flow control assembly. When installed, I didn't change out the restrictor(or gicleu...... Read more answer now
      Asked by Robert on August 6, 2019 10:56 pm
      Answered by the admin

      We are very sorry to hear about this. Unfortunately, we only have the kits. We will find out from Lelit if can get the needle separately. However, they are closed for the month of August.
      45. can work with Faema E61?
    45. 0 votes
      Q can work with Faema E61? answer now
      Asked by Nelson on July 27, 2019 9:40 am
      Answered by the admin Sorry, as we indicate, we can not guarantee a fit on every E61 grouphead as there are slight differences between manufacturers. For Faema machines, this kit most likely will NOT work on the Legend series.
      46. Will this work on the Rocket Appartamento?
    46. 0 votes
      Q Will this work on the Rocket Appartamento? answer now
      Asked by David Hersh on July 23, 2019 12:27 am
      Answered by the admin

      Sorry, we can not guarantee it 100% as we do not carry this machine. It should work, but there could be some nuances like a new mushroom needed.
      47. I have installed this kit on a Profitec 700. My Profitec has the old two piece mushroom so the Lelit kit fits like a glove. I am having a terrible time trying to control the pressure with the paddle. From what I have read online the water debit for the Lelit Bianca is about 6.3ml/s in the fully opened position. On the Profitec with the Lelit kit I am getting about 9.2ml/s in the fully open position and no flow in the fully close position. I also have set the pump pressure at 10bars and the OPV at 11bars. In every video I have watched the pressure ramp up seems to be relatively slow even with the paddle fully opened. This allows the user to slow the flow to 2, 3 or 4 bars for several seconds by moving the paddle clockwise. In my case even with the paddle opened only 20% the ramp up is almost instant giving me no chance whatsoever to have any control. The only way to stop it is to fully close the paddle, but then it drops to 0bars. I have been experimenting with all types of grind settings, but nothing works. In short the group gauge behaves just like if I had a blind disk on the portafilter. I would really appreciate if you could contact me via my email with some suggestions. Thx in advance.
    47. 0 votes
      Q I have installed this kit on a Profitec 700. My Profitec has the old two piece mushroom so the Le...... Read more answer now
      Asked by Wally on July 16, 2019 9:56 pm
      Answered by the admin

      Thanks for the inquiry. Two things... please try to coarsen your grind. The brew gauge is showing the resistance created by the ground espresso coffee in the filter basket. When the grinder is finer than it should be, we see the ramp up pressure higher. Second, lift the lever to the pre-infusion stage to release any excess pressure in the coffee boiler. Either one solution separately or both together can improve your situation.

      The other issue may be if there are gicleurs in the tubes from the coffee boiler to grouphead. The hole may be too large or there may be no gicleurs at all. Lastly, if there is a pre-heat of the incoming water to the coffee boiler by the steam boiler, this may be adding excess pressure in the coffee boiler. We are unsure on this latter point as we do not sell the Profitec line at this time.
      A The Profitec 700 does not have any pre-heating of the incoming water and the only gicleur is the one provided with the Lelit flow kit. I checked it and it is definitely not lose. There are no other gicleurs in the pipes or anywhere else. Something is definitely not right. I certainly hope I didn't throw $325 dollars away.
      A I have to add that the flow I am now getting on the Profitec 700 with the pressure set at 10bars per Lelit and other Bianca users is 10ml/s instead of 6.3ml/s. The only way for me to get 6.3ml/s is with the paddle set in an almost close position(less than .5 inches travel between a flow of 6.3ml/s to fully close 0ml/s. This makes the operation of flow profiling impossible. I am convinced that I got a defective Lelit Flow Control Kit. Maybe the machining of the needle and/or gicleur was wrong or something. I really don't know, but something is definitely wrong. Is there a better way to get technical support than this Q & A form? Thx.
      48. I recently bought the flow kit from you and installed it in a Profitec 700. My Profitec has the old two piece mushroom so the Lelit kit fits like a glove. The brew pressure is set at 9bar and the OPV is set at 11bar. I have the paddle set to fully close the flow on the left almost touching the machine case. When the paddle is fully open(all the way to the right) I get a water debit of 9.3ml/s. This is more than what the Bianca users are getting(6.3mls). I don't know if that is the main reason, but I am having a terrible time trying to control the flow during a shot. In every single video I have seen of the Bianca even with the paddle fully opened the pressure ramp up on the group gauge is pretty slow. This makes it possible to stop the pressure at 2 bars for example during preinfusion. In my Profitec the ramp up is way too fast which makes it impossible to have any control. Even with the paddle opened 10% the ramp up is almost instantaneous. With this behavior it is impossible to have any profile control. Any idea what could be the problem? Thx in advance.
    48. 0 votes
      Q I recently bought the flow kit from you and installed it in a Profitec 700. My Profitec has the o...... Read more answer now
      Asked by Wally on July 16, 2019 7:37 am
      Answered by the admin

      Some answered on another question. Also, if there is co control at all on flow, even in closed position, this means the installed gicleur may have been in too loose. However, do not over-tighten.
      49. Why won't the valve work with the Vibiemme group head? Is the Vibiemme thread different than the valve thread? Does the valve seat thread not match? Is the needle too long for the Vibiemme mushroom? Is there some other problem? What needs to be resolved or reworked to make it work?
    49. 0 votes
      Q Why won't the valve work with the Vibiemme group head? Is the Vibiemme thread different than the ...... Read more answer now
      Asked by Curtis Ide on July 4, 2019 5:27 pm
      Answered by the admin Sorry, it will not work under its current form. The lower portion of the paddle is obstructed by the design of the grouphead shape which is more robust, but not round. The only workaround is to chop off the bottom portion of the paddle.
      50. My espresso machine is Lelit Mara. With the paddle fully open, my flow rate decreases to a mere ~1.6 ml/sec. Is that normal? Should I replace the gicleurs when I put in the paddle? The answer will be no, if they are the same. Thanks,
    50. 0 votes
      Q My espresso machine is Lelit Mara. With the paddle fully open, my flow rate decreases to a mere ~...... Read more answer now
      Asked by Robert Wu on June 26, 2019 6:06 pm
      Answered by the admin

      The gicleur with the Bianca paddle kit has a different size hole, so the new gicleur should be installed.
      51. Can it install to Rocket 58, ECM Synchonika, or Profitec Pro700?
    51. 0 votes
      Q Can it install to Rocket 58, ECM Synchonika, or Profitec Pro700? answer now
      Asked by Tien Dong on June 5, 2019 2:52 pm
      Answered by the admin

      Sorry, we can not confirm yes or no if it will fit perfectly. There are different versions of the E61 grouphead. However, if you are willing to work through the process through trial and error, we are pretty sure it can be done. For instance, a ECM mushroom and gasket may be needed.
      52. I have a Lelit PL62 and I want to buy the flow control upgrade kit. I never opened my E61 group head for maintenance, and I have the PL62 for about 4 years. Do you think that I need to buy some additional parts just in case I have to replace it?
    52. 0 votes
      Q I have a Lelit PL62 and I want to buy the flow control upgrade kit. I never opened my E61 group h...... Read more answer now
      Asked by Avihay Zaguri on May 28, 2019 3:05 pm
      Answered by the admin Per Lelit, no additional parts should be needed.
      53. is there a way to add this to a vibiemme e-61 group head? Any idea?
    53. 0 votes
      Q is there a way to add this to a vibiemme e-61 group head? Any idea? answer now
      Asked by felipe on May 27, 2019 11:06 am
      Answered by the admin

      Sorry, at this time, this kit will not fit the Vibiemme due to the shape of the grouphead. However, do not lose hope as there may be a solution some day.
      54. Would I need any of the other mushroom parts for a Vesuvius?
    54. 0 votes
      Q Would I need any of the other mushroom parts for a Vesuvius? answer now
      Asked by dbsutherland77 on May 26, 2019 9:32 pm
      Answered by the admin

      Sorry, we are unable to answer this question at this time as we do not have a Vesuvius to test this on.
      55. Do you know if this kit will work with an Izzo Alex Duetto II?
    55. 0 votes
      Q Do you know if this kit will work with an Izzo Alex Duetto II? answer now
      Asked by Randy on May 20, 2019 7:35 pm
      Answered by the admin

      Sorry, we do not have confirmation at this time. If there is a stainless steel mushroom without the separate nut on top of the mushroom, a new mushroom with gasket will be needed.
      56. Quickmill e61 group head suitable for this kit?
    56. 0 votes
      Q Quickmill e61 group head suitable for this kit? answer now
      Asked by Dani on April 18, 2019 7:19 pm
      Answered by the admin

      We are pretty sure it does. However, we will need to have feedback from one of our pre-order customers.
      57. Do you know if this kit will work on Bezzera E61 group head?
    57. 0 votes
      Q Do you know if this kit will work on Bezzera E61 group head? answer now
      Asked by Tsur on April 18, 2019 5:59 pm
      Answered by the admin

      Sorry, we have not confirmed yet. As soon as we do, we will update this page.
      58. Would this work on a Rocket Giotto Premium Plus v2 (don't believe there is much difference if any on older or newer GPP's in terms of grouphead design)
    58. 0 votes
      Q Would this work on a Rocket Giotto Premium Plus v2 (don't believe there is much difference if any...... Read more answer now
      Asked by Justin on April 12, 2019 7:47 pm
      Answered by the admin We are very sorry that we could not confirm yes or no on this question as we do not sell Rocket at this time.
      A It works on my Rocket Giotto Revoluzione.
      59. How do I order the two parts of this kit w/o the pressure gauge since I already have one? It shows separate pricing on SKU: 1000185 ($149.96) and SKU: 410003 ($67.46), but no way to select them separately.
    59. 0 votes
      Q How do I order the two parts of this kit w/o the pressure gauge since I already have one? It show...... Read more answer now
      Asked by Jim on April 11, 2019 1:49 am
      Answered by the admin Sorry, it is only available as a complete package with the discounts. We may sell the items separately in the future, but the pricing will be higher for each.