ECM S-Manuale 64 Espresso Grinder
The ECM S-Manuale 64 is one of ECM’s semi-automatic espresso grinders. The stepless wormgear adjustment allows for very fine grind tuning. This allows for easy compatibility with any espresso machine and espresso blend.
Grinding adjustment
- Stepless – Gives you access to an “infinite” number of grind settings. This allows you really fine tune your grind fineness of your coffee beans. The numbered dial underneath the hopper helps you remember your current grind setting easier.
- Adjustment knob – Located in the rear of the machine just below the hopper. Turning the knob clockwise will make the grind finer. Turning counterclockwise will make the grind coarse.
Grinding burrs
- Flat burrs – Large size at 64 mm. The larger the size, the more of a grinding surface, resulting in faster production.
- High rpm – Faster spinning rate at 1400 rpm. The higher the speed, the faster the production, which can increase efficiency and reduce wait times.
- Easy access – Remove the bean hopper & the set screw. There are 3 Allen key screws (~2.3 mm) that hold the upper holder in place. After removing the screws, turn the upper burr holder counter clockwise until the top assembly comes off. This will give you access to the burrs and the grinding chamber. The burrs themselves are held in with 3 flat head screws.
Semi-automatic grinding
- Easy operation – The long vertical plate activates a microswitch. This is what starts the grinding process. The plate extends below the fork if you are grinding into the container.
Bean hopper
- Low profile – There are 2 hoppers available for the ECM S-Manuale 64. We include the shorter hopper with our grinders. The total height of the grinder is approximately 16.5.” It should easily fit under standard 18″ overhead cabinets.
- Set screw – Secures the hopper to the grinder. Serves as a reminder for users from quickly removing the hopper if it is full of beans.
- Finger guard – Prevents users from “accidentally” putting their fingers in the grinding burrs.
- Stopper – A door near the bottom of the hopper can be pushed in to close the opening. This allows you to remove the hopper with beans inside so you can easily change the beans. There will be some beans already passed in the burrs which you will have to grind out first before removing the hopper.
Portafilter fork
- Ease of use – Accommodates most portafilters. The clearance from the fork to the funnel is approximately 2.25.”
- Container grinding – The forks requires a wrench to remove the holding nut. However the coffee funnel and fork sit high on the grinder. You can fit any small container (under 4.25″) underneath the fork.
Grinds catch tray
- Easy to “install” – There are no screws The tray has 2 holes that hook to the front legs of the grinder. This ensures that the tray won’t slide away from the grinder.
- Convenient – As easy as it is to install, it’s just as easy to remove to discard any excess grinds. There are other comparable models that do not have a tray at all.
Notes
Espresso Coffee Grinder Warnings:
- Changing grind settings: It is very important to only change grind settings when the unit is powered on and the burrs are in motion. If you do not do this, the burrs will ‘gunk’ up and render the grinder to only produce very coarse grinds or no grinds at all. To remedy this, you will have to open up the grinder to get access to the grinding burrs. This issue will be considered operator error for lack of following directions, and not be classified as a defective grinder.
- Electrical cord: The cord is placed between the packaging (foam or cardboard) and the underside body of the grinder. During shipping, it is normal for a bend or insignificant blemish/slice to damage the cord.
- Finding coffee grinds in a new grinder: We have confirmed that the manufacturer tests EVERY grinder with coffee beans before it leaves their facility. Unfortunately, they are not always able to get every trace of coffee out of the grinders after testing. As a result, you may find coffee beans or grinds inside your grinder, or there may be grinds in the packaging.
- Static issues: There are static issues with all grinders, even the highest-quality models. We firmly believe that the static comes from the coffee beans. If you are having static problems with your coffee grinder, try using a different blend of beans.
- Electrical: To avoid electrical damage (which is not considered a manufacturer’s defect), please acquire and install a single-outlet surge suppressor rated at 1080 joules or higher. A surge without protection can damage a grinder at the power switch, the capacitor, the motor, or the wiring.
- Burr cleaning: For routine maintenance of the grinding burrs, we recommend using grinder cleaning agents. We do not recommend any removal of the burrs or the burr carrier for cleaning (unless absolutely necessary) as re-assembly can cause damage.
- Replacing burrs: NEVER use a flathead screwdriver and hammer to wedge under the burrs for removal. This could badly damage your grinder.
Specifications
| Brand | ECM Manufacture |
|---|---|
| Height (inches) | 16.5, approximate |
| Width (inches) | 6, approximate |
| Depth (inches) | 8, approximate |
| Weight (pounds) | 15 |
| Wattage (watts) | 450 |
| Voltage (volts) | 110 – 120 |
| Burr size (mm), Type | 64, flat |
| Grinding speed (RPM) | 1400 |
| Hopper capacity (grams) | 500 |
| Country of manufacture | Germany |
| Approvals | CE |
Reviews
There are no reviews yet.